氧化钪中Ti,Mo,W,V,Zr等难熔杂质光谱分析

本用提高样品蒸发速率的方法提高氧化钪中难熔杂质光谱分析灵敏度。采用一种特殊的阴极设计，配合使用Ｎ２＋Ａｒ气氛控制，在旋流气室中放电激发，取样仅５ｍｇ的条件下，光谱测定氧化钪中难烷质Ｔｉ，Ｚｒ，Ｍｏ，Ｗ，Ｖ灵敏度可达（１－３）×１０＾－４％。测定的相对标准偏差为９％－２７％。     

吸波材料与微波暗室问题的数学模型

为分析尖劈形材料的吸波性能,建立了半圆镜像模型将辐射波在尖劈空间的传播等效为射线对等分半圆的切割,确定了反射波线和吸波材料几何参数之间的解析关系.对于微波暗室问题,假设在余弦辐射体上随机选取一个方向的能量波束集中了其所有能量,分别建立了加权能量分布模型和Monte Carlo模型,仿真验证了两模型结论的一致性.     

真空冷却过程中实验条件对真空冷却速率的影响

以熟肉为实验材料,对实验条件对真空冷却速率的影响进行了理论分析和实验研究。实验结果表明:真空室有效容积越小、真空泵抽速越高,则真空冷却时间就会越短;冷阱温度对真空冷却速率有着明显的影响;当真空室内的最终压力在0.4～0.61kPa变化时,熟肉的表面温度一直在0℃以上,其真空冷却的时间随着真空室内压力的升高而增加。而真空室内的最终压力在0.3kPa左右时,熟肉的表面温度在真空冷却过程会低于0℃。     

LC–MS/MS determination and interaction of the main components from the traditional Chinese drug pair Danshen–Sanqi based on rat intestinal absorption

The Chinese drug pair Danshen (Salvia miltiorrhiza)–Sanqi (Panax ginseng) has been widely used for centuries treating various cardiovascular disorders, among which salvianlic acid B (SAB), ginsenoside Rg₁ (GRg₁), ginsenoside Rb₁ (GRb₁) and notoginsenoside R₁ (NGR₁) were identified as the major components. The present study focused on the interaction between these components based on investigating their intestinal absorption using the Ussing chamber technique. The concentrations of SAB, GRg₁, GRb1 and NGR₁ in the intestinal perfusate were determined by LC–MS/MS method, followed by Q (accumulative quantity) and P_app (apparent permeability). The results showed that all these four main components displayed very low permeabilities, which implied their poor absorption in the rat intestine. The intestinal absorption level of SAB displayed regioselectivity: duodenum < jejunum < ileum. However, there was no significant difference in the absorption of GRg₁ and GRb₁ in the different segments. The Q and P_app values of the four main components were obviously increased in jejunum when co‐administrating Danshen extract with Sanqi extract. In conclusion, compatibility of Danshen and Sanqi could remarkably improve the intestinal absorption level of the main components in the pair. To some extent, this might explain the nature of the compatibility mechanisms of composite formulae in TCMs.     

衰减振荡电流下火花电阻的光谱诊断

气体开关是脉冲功率系统的关键部件,开关的火花通道阻抗直接影响负载电压的陡度及其能量传输效率。提出一种光谱学诊断方法,通过对火花通道成像光谱的时空分辨测量,获得通道半径及电导率,从而计算时变的火花电阻。光谱测量结果表明,氮气间隙火花放电通道电子温度为2~3eV,通道电导率先增大后减小,最大值约16 000S,随着放电发展,火花通道电阻从绝缘状态快速跌落并趋于稳定值,时变趋势与电学计算结果基本吻合。3~100kPa范围内,随着气压增大,放电通道半径减小,火花通道电阻增大。     

相关光谱式气体检测系统的光学仿真及优化

依据相关光谱式红外气体传感器检测原理,以系统中红外光与气体反应的气室为研究对象,利用光学设计专用软件Tracepro对理想红外朗伯光源在不同反射镜类型下光源的最佳位置进行了仿真分析;通过建立光路传输系统的数学模型,对气室不同结构尺寸下的光功率输出、以及气室内壁反射率对传感系统性能的影响进行了仿真与优化.在理论模型的基础上,根据仿真结果,确定了最佳气室模型的参数组合.实验结果表明,通过对气室中红外光源的位置、反射镜类型、气室长度等部分进行适当的优化修改后,可使探测器接收信号幅度得到明显提高,将有利于后级电路的信号放大、数模转换等处理过程,从而提高气体浓度检测的灵敏度和精度.     

电脉冲沉积铝化物及铝化物-Y_2O_3涂层

采用电脉冲沉积技术在 2 0碳钢表面上获得了冶金结合的晶粒尺寸约为几十到几百纳米的铝化物和铝化物 弥散Y2 O3复合微晶涂层。60 0℃空气中氧化 10 0h的结果表明 ,电脉冲沉积获得的两种涂层均可显著地降低 2 0碳钢的氧化速率并提高氧化层的抗剥落性能。用AFM ,SEM ,EDS和XRD对铝化物涂层及氧化层进行了分析 ,并讨论了两种涂层提高抗氧化性能的作用机制     

软X射线监测系统的建立与国际标准的比对

软Ｘ射线监测系统的建立，结构特点和性能，有效地解决了气体的吸收和窗膜的透过率等因素的影响。申请获得了美国布鲁克海文国家实验室（ＢＮＬ）的用光时间，对监测系统的性能进行研究，并给出了该系统的精度及与国际标准的比对结果。     

Characteristics of high energy interactions I. High energy gamma-ray spectra near the top of the atmosphere

An emulsion chamber was used to study the characteristics of high energy nuclear interactions from the production spectra ofγ-rays. The emulsion chamber, which comprised of two parts, namely the detector and the graphite producer unit, was exposed to cosmic rays for about 7 hr at an atmospheric depth of 10 g cm⁻² at Hyderabad (geomagnetic latitude 7·6°N). 720 electromagnetic cascades due toγ-rays were recorded in the detector. These cascades were classified into three groups; (a)γ-rays from nuclear interactions in the detector (b)γ-rays from nuclear interactions in the producer unit and (c)γ-rays of atmospheric origin. The energies of the cascades were determined using photometric method. The spectra ofγ-rays from groups (a) and (c) were determined and compared with similar spectra obtained at greater atmospheric depths. The spectra were found to obey a power law. The spectrum ofγ-rays of atmospheric origin was found to steepen at high energies,E _r>2200 GeV.     

Microstructural prototyping of ceramics by kinetic engineering: applications of spark plasma sintering

The significance of kinetics on the development of microstructures in connection with sintering of ceramics is well recognized. In practice, however, it still remains a challenge to prepare designed microstructures via engineering the sintering kinetics because of an insufficient understanding of the different operative mechanisms that are in many cases overlapping. In this article the kinetic issues involved in sintering are described and discussed with respect to their potential for prototyping microstructures that yield desired properties. By exploiting and mastering the differences present in the kinetics of grain sliding, densification, chemical reactions, and grain growth, respectively, we have established processing principles for producing bulk ceramics with microstructures consisting of nano-sized grains, aligned grains, and/or non-equilibrium-phase constitutions, and for achieving radically improved superplasticity in brittle ceramics. Although the studies quoted in this article were mainly carried out by spark plasma sintering, more general implications of them are expected, including efficient particle sliding, deformation-induced dynamic ripening, superplastic deformation-induced dynamic ripening, and non-equilibrium integration.